Pracovná plošinová náves

ES-GE 5-Achs-Ballastauflieger

Our complete range of vehicles, including those available immediately and at short notice, can be found on our website.

Below is an excerpt from the equipment/features. Full equipment list available on request.

Chassis:
* Welded construction made of high-quality steel profiles with through cross beams, designed for high point loads
* Outer frame made of UNP steel

Coupling Device / Fifth Wheel Load:
* 2-inch kingpin
* Tech. permissible fifth wheel load: 26,500 kg

Underrun Protection:
* According to EC regulations, bolted design

Side Impact Protection:
* According to EC regulations

Landing Legs:
* Landing legs with one-sided operation, support load approx. 66 t/lifting capacity approx. 24 t

Axles:
* 5 x 10 t air suspension axle units, SAF make, with drum brake approx. 400 x 200 mm
* ABS
* Centrally positioned 10-stud wheel bolt pattern, offset 0
* Total lift of air suspension approx. 200 mm (lift approx. 140 mm, lower approx. 60 mm), control via rotary lever valve with detent feature

Steering:
* 1st axle mechanically steered, 2nd axle fixed, 3rd, 4th, and 5th axles with forced mechanical steering (Tridec)
* Centralized grease points extended to outer side

Axle Lift:
* First and second axle automatically liftable, with additional cut-off switch on the chassis

Braking System:
* Two-line compressed air brake system to EC standards with EBS and RSS, automatic load-dependent control, Wabco 4S/3M make
* Spring-loaded cylinders as parking brake
* Interchange-proof coupling heads permanently attached to the front cross member, without connecting line to tractor unit
* Aluminum air tank

Tyres:
Gkodpfx Aowx Dcaogusc
* 10 x 445/65 R22.5 164J on rim 11.75 x 22.5 offset 0 – manufacturer of our choice

TPMS:
* Tyre pressure monitoring system
* TPMS in accordance with ECE R141, with data transfer to tractor unit

Mudguards:
* In line with EC regulations, 1st axle front, 2nd axle rear, 3rd, 4th, and 5th axles each with quarter PVC mudguard front and rear
* Rear mudguards with splash flaps

Load Securing:
* 5 pairs of folding lashing rings, evenly distributed (tensile force approx. 14 t)
* 11 pairs of welded hook plates in the outer frame (tensile force approx. 3 t)
* 10 pairs of side lashing rings in the outer frame, evenly distributed (tensile force approx. 8 t)

Stanchion Pockets:
* 10 pairs of stanchion pockets recessed in the outer frame
* 6 pairs of stanchion pockets recessed in the floor (on the outer longitudinal member)

Plug-in Stanchions:
* 16 galvanized plug-in stanchions, approx. 80 x 80 x 8 mm, usable length approx. 850 mm

Stanchion Magazine:
* On each side in front of the bulkhead, one magazine for 8 plug-in stanchions each, approx. 80/80 mm

Bulkhead:
* Bolted corner posts filled with aluminum hollow profiles, inside with a steel wear plate over the full width and height

Floor:
* Approx. 28 mm Z-hardwood floor, recessed and flush in outer frame

Lighting System:
* In accordance with EC regulations, 24 V with multi-chamber lights
* LED side marker lamps
* LED position lights front white
* LED outline marker lamps at the rear
* License plate lamps
* 1x15 and 2x7-pin sockets on the front cross member

Equipment:
* Double chock holder
* ECE 70 warning panel
* Work floodlight on light carrier (activated via reverse gear)
* Holder for rotating beacon at the rear (incl. beacon)
* 1 fixed access ladder left and right each side, incl. plug-in step aid
* Smart Board
* "Vehicle swings out" sign
* Load center of gravity indication sticker

Paintwork:
* Chassis

Inzercia bola automaticky preložená a vyskytli sa nejaké chyby prekladu.