Hydraulický stĺpový lis

Hidralmac 500 T Säulenpresse 2100 x 1500 mm

Pressure: 500 t

Clear passage width: 2,100 x 1,500 mm
Stroke: 1,000 mm
Total power requirement: 62 kW
Approx. machine weight: 39 t
Dimensions L x W x H: 5,100 x 2,800 x 4,040 mm
Retraction force: 40 t
Main cylinders: 2 units
Column diameter (main cylinder): 360 mm
Table size: 2,100 x 1,500 mm with T-slots
Ram size: 2,100 x 1,500 mm
Table height above floor (approx.): 850 mm
Forward speed: 300 mm/sec
Return speed: 300 mm/sec (with 20T ram weight)
Pressure phase speed: 28 mm/sec at 200T
Oil tank: approx. 1,000 l
Auxiliary cylinders: 2 units
Column diameter (auxiliary cylinder): 120 mm
Overall table plate size: approx. 2,750 x 1,600 mm
Overall ram plate size: approx. 2,750 x 1,600 mm
Pressure phase speed: 20 mm/sec at 300T
Pressure phase speed: 6 mm/sec at 500T
Ram retraction force: 40 t
Control circuit voltage: 24 V
Voltage: 400 V
Frequency: 50 Hz
Axial piston pump (REXROTH/Bosch A4VSO125): 290 l/min
Installation height (distance work table–ram plate): 1,500 mm
Hydraulic block: REXROTH
Pressure control: via PLC (minimum pressure 50T)
Cylinders: 4 x ?90 x 70 mm
Stroke length: 300 mm, adjustable via PLC
Ejector forward speed: 95 mm/sec
Ejector return speed: 240 mm/sec
Capacity: 4 x 15T at 250 bar
Pressure adjustment: via monitor, 50–500T
Pressure holding time: 0–900 sec
Hydraulic tank: 2,000 l
Control system: Siemens S7 300
Memory capacity: 200 programs
Electronics from German manufacturers: SIEMENS / MÖLLER
Control panel: on swing arm
Light sensors Sick: 1,500 mm (front)

Control functionality:
The linear scale continually communicates the position of the ram and ejectors to the controller. Travel path, upper limit, and switching position where the press changes from idle stroke to working speed, as well as the target end position, can be set easily and quickly via the monitor control.

The working speed can be regulated in 1 mm/s increments from 0 to 10 and in 10 mm/s increments from 10 to 300 mm.

The machine includes a pressure monitoring system that either raises the ram when the set pressure is reached, or holds pressure constant for the set time (within 5% tolerance) before opening.

The controller monitors secured areas, the entire hydraulics, the pumps, and temperature. Additionally, it synchronizes the main cylinders and compensates for uneven loads.

The control is housed in a separate cabinet. Actual press operation occurs via a control panel mounted on a swing arm, reducing operator travel distances.

Additional equipment:
- 8 mm polycarbonate glazing inside rear door
Bsdpfedyynvex Afwolr
- 8 mm polycarbonate glazing in the side doors and working area
- Liquid channel (25 mm radius) at front, rear, and sides of the table

Special features of the press:
- Including 10% reserve (maximum capacity 550 t)
- Steel grade: stainless steel LCG ASTM A36, manufactured according to DIN 8651
- Motor and pump shut down once the tool is closed and automatically adjust for 5% pressure loss (major cost savings)

Nitrogen compression unit:
A nitrogen compression unit is included, generating a sudden pressure of 280 bar, with on/off capability.

Inzercia bola automaticky preložená a vyskytli sa nejaké chyby prekladu.