Pracovná plošinová náves

FAYMONVILLE MAX Trailer MAX210 Telesattel

Stav: nový, celková hmotnosť: 48 000 kg, maximálna hmotnosť nákladu: 38 400 kg, konfigurácia náprav: 3 nápravy, celková šírka: 2 540 mm, Výbava: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from equipment. Full specifications available upon request. Load Area: * Extendable load area with pneumatically operated locking mechanism * Load platform with approx. 30 mm thick hardwood floorboards * 7 pairs of folding lashing rings to the outside (LC 5,000 daN) * 3 pairs of folding lashing rings to the outside (LC 10,000 daN) * Cut-outs in the outer frame of the loading area for hooking in tensioning straps (LC 2,000 daN) Landing Legs: * JOST mechanical landing legs with 2-speed gearbox, 24 t lifting capacity (50 t test load) Tyres: * Tyres: 385/65 R 22.5 Axles: * BPW axles and suspension, all axles hydro-mechanically steered * Equipped with disc brakes * Technical axle load: 10,000 kg (offset 0) * Air suspension with raise/lower valve Braking System: * WABCO braking system according to EU regulations with EBS-E (2S2M), without connecting lines to the tractor unit Paintwork: Fjdpfxexl Nf Ds Agusgh * High-quality 2-component (2K) top coat, single colour, RAL 3002 Carmine Red Accessories: * Remote-controlled steering from the front and rear via cable remote (pushbutton operation), with single axle tracking control. (No installation in the tractor unit) * Electro-hydraulic power pack * 4 chocks with holders on the front wall * 2-inch kingpin * Yellow-red air couplings on the galvanized connection bar at the front * Bracket for beacon at the rear of the trailer * 10 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the loading platform * 1 spare wheel holder under the loading area, right side in direction of travel (without spare wheel) * Load gauge (manometer) for axle load determination, including load diagram Including Special Equipment: * Galvanized steel front wall (EN12642-XL), approx. 1,600 mm high * 6 pairs of WADER container locks in the load platform, suitable for 1 x 20' container, 2 x 20' containers or 1 x 40' container; when extended, additional locking position for a 45' container * 4 pairs of crosswise-mounted stake pocket rails in the load platform, for plug-in stakes approx. 100 x 50 mm * Storage for up to 9 pairs of plug-in stakes, screwed inside the front wall * Access ladders mounted left and right in direction of travel * 1 stainless steel (INOX) toolbox, approx. 1,200 x 460 x 550 mm, mounted at the front under the loading platform, left side in direction of travel * 1 extra stainless steel (INOX) toolbox, approx. 1,200 x 460 x 550 mm, under the loading platform, left side in direction of travel * Load platform with approx. 30 mm thick wood floor enclosed in Omega profiles * Lifting axle on the front axle, controlled by TEBS E * BEKAMAX (Pico) central lubrication system with standard NLGI-2 grease * 2 LED reversing spotlights mounted on the rear panel * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear * HRM metalization (High Resistance Metallization)

Stav: použitý, celková hmotnosť: 48 000 kg, maximálna hmotnosť nákladu: 38 080 kg, konfigurácia náprav: 3 nápravy, prvá registrácia: 02/2025, ďalšia kontrola (TÜV): 02/2026, celková šírka: 2 540 mm, Výbava: ABS, Our complete stock of immediately and shortly available vehicles can be found on our website. Excerpt from equipment. Complete equipment list available on request. Loading platform: * Extendable loading platform with pneumatic locking * Loading platform with approx. 30 mm thick wooden floor, framed in omega profiles * 7 pairs of exterior foldable lashing rings (LC 5,000 daN) * 3 pairs of exterior foldable lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the loading platform for hooking in tensioning straps (LC 2,000 daN) Landing legs: * JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension * All axles are hydro-mechanically forced-steered * With disc brakes * Technical axle load: 10,000 kg each (ET 0) * Air suspension with lifting and lowering valve * Axle tools Tyres: * Tyres: 385/65 R 22.5 Brake system: * Brake system according to EU regulations with EBS-E (2S2M), without interconnections to the tractor Warning boards: * Bracket for warning boards on gooseneck and rear end, left and right, including socket Electrical system: * Electrical system in accordance with EU regulations * Lighting: 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the front connector strip with sockets 24N, 24S & 15-pin, connections according to ISO 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel construction: * High-strength fine grain steel construction * Steel grades S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690MPa) Paintwork: * Premium and durable corrosion protection of the standard shot-blasted welded frame secured by a 2-component (2K) zinc-rich primer * High-quality 2-component (2K) top coat, single colour in RAL 3002 carmine red * Rims in silver; attachments as per manufacturer’s choice * Rear section metalized and coated in RAL 9010 (pure white) Accessories included: Fgjdpoxf Sifsfx Agush * 2 inch kingpin * 4 chocks with bracket on the front wall * Steering from front and rear controllable via cable remote with pushbuttons, with axle tracking control (without installation in the tractor unit) * Manual and documentation on USB stick * Electro-hydraulic power pack * Galvanised connector strip at the front with yellow-red air couplers * Yellow reflective tape in accordance with EU regulations on the sides, extension, and rear of the trailer * European reflective panels (red-yellow) at the rear of the trailer * One mudflap at the rear of the trailer * Mount for a revolving beacon at the rear of the trailer * 10 pairs of stake pockets for 100 x 50 mm drop-in stakes in the outer frame of the loading platform * 1 spare wheel carrier under the platform on the right-hand side * 80 km/h speed sticker on the rear and both sides * Load gauge for determining axle loads, including load diagram * Galvanised steel front wall (EN12642-XL), approx. 1,600 mm high * 6 pairs of WADER container pockets in the deck, for 1 x 20' container, 2 x 20' containers, or 1 x 40' container; an additional locking position is provided in the extension area for a 45' container * 4 pairs of transverse stake pocket rails mounted in the loading platform for approx. 100 x 50 mm drop-in stakes * Storage for stakes inside on the front wall * Access ladder mounted on left and right in direction of travel * One INOX toolbox, approx. 1,200 x 460 x 550 mm, front left under the platform * Additional tools (sentence unfinished in the source) Note: Please request the complete l

Stav: použitý, celková hmotnosť: 48 000 kg, maximálna hmotnosť nákladu: 36 300 kg, konfigurácia náprav: 3 nápravy, prvá registrácia: 08/2024, ďalšia kontrola (TÜV): 08/2025, celková šírka: 2 540 mm, Výbava: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. Excerpt from the equipment list. Full specification available on request. - Loading platform in double extendable design with pneumatically operated locking mechanism - The center beam is fitted with a fixed intermediate table approximately 250 mm wide - BPW axles and suspension, all axles hydro-mechanically forced steered - Air suspension with lift and lower valve Fgodopkx Eaepfx Agueh - Tyres: 385/65 R 22.5 - JOST landing legs (mechanical) with 2-speed gearbox, lifting capacity approx. 24 t (test load approx. 50 t) - Brake system complying with EU regulations with EBS-E (2S2M) - Disc brakes - 2-inch king pin - Electro-hydraulic unit - Remote steering at the front and rear via cable remote control - 10 pairs of stake pockets for insertable stakes approx. 100 x 50 mm in the outer frame of the loading area - Load gauge for axle load determination including load chart - Galvanized steel front wall (EN12642-XL), approx. 1,600 mm high - 6 pairs of WADER container pockets in the loading area, for 1 x 20' container, 2 x 20' containers or 1 x 40' container; an additional locking point is provided in the extension for a 45' container - 5 pairs of crosswise mounted stake pocket rails in the loading area - Storage for up to 9 pairs of insertable stakes approx. 100 x 50 mm, inside at the front wall - One INOX toolbox each, approx. 1,200 x 460 x 550 mm, mounted front left and right below the loading platform - Centralized lubrication system with 2 BEKAMAX (Pico) pumps - 2 LED reversing lights mounted on the rear panel - Acoustic reversing warning signal - Bumper protection left and right at the rear cross member - 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear - HRM metallization (High Resistance Metallisation) - Single-color finish in RAL 3002 carmine red

Stav: nový, celková hmotnosť: 48 000 kg, maximálna hmotnosť nákladu: 34 660 kg, konfigurácia náprav: 3 nápravy, celková šírka: 2 540 mm, Výbava: ABS, Our complete vehicle inventory, including immediately and short-term available vehicles, can be found on our website. Excerpt of equipment. Full specification available on request. Loading platform * Double-extendable design with pneumatically operated locking mechanism * 2 pairs of flush-mounted lashing rings (LC 5,000 daN) * 1 pair of flush-mounted lashing rings (LC 10,000 daN) * 7 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) Landing Legs * JOST mechanical landing legs, 2-speed gearbox, approx. 24 t lifting capacity (test load approx. 50 t) Tyres * 235/75 R 17.5, 3PMSF Axles * BPW axles, hydro-mechanically forced-steered * Air suspension with raise/lower valve Brake system * In accordance with EU regulations with EBS-E (2S2M) without connection lines to the tractor unit Steel construction * Made from high-strength fine-grain steel. Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork * Premium, durable corrosion protection of the standard shot-blasted welded frame guaranteed by 2-component (2K) zinc dust primer * High-quality, single-color 2-component (2K) topcoat finish in RAL 3002 carmine red * Rear section metallized and painted in RAL 9010 (pure white) * Rims in silver Incl. Accessories * Remote rear and front steering control via cable remote with push buttons, with single-track monitoring of the axles (without installation in tractor unit) * Electro-hydraulic unit * 4 wheel chocks with holders on the front wall * 2-inch kingpin * Yellow-red air couplings on the galvanized connection plate at the front * Yellow reflector tape according to EU regulations at the sides, extension and rear of the trailer * European reflective plates (red-yellow) at the rear of the trailer * One mudflap at the rear of the trailer * Manual and documentation on USB stick * Loading platform with heavy-duty hardwood floor * 10 pairs of stake pockets for plug-in stakes 100 x 50 mm on the outer frame of the loading platform * Mounting bracket for beacon at the rear of the trailer * Galvanized supports under the tapered section of the loading platform * Mounting bracket for beacon at the rear of the trailer * Mounting rail for ALU drive-on ramps at the rear of the vehicle * 80 km/h speed stickers at the rear and both sides Fgjdpfx Agjk Ugacoush * Load gauge to determine axle loads incl. load diagram * Galvanized steel front wall (EN12642-XL), approx. 1,600 mm high * Central lubrication system with 2 BEKAMAX (Pico) pumps, NLGI-2 standard grease, and removable protection around the pumps * Spiral cable to supply the electro-hydraulic unit and/or electric winch (approx. 35 mm², approx. 3.5 m, max. 250 A), between trailer and tractor unit with plug connection (NATO-NATO) * Painted sand layer on the central beam as anti-slip * 6 pairs of WADER container locks in the loading platform for 1 x 20' container, 2 x 20' containers or 1 x 40' container; an additional locking point is provided in the extension for a 45' container * 5 transverse rows of stake pocket strips in the loading platform for plug-in stakes 100 x 50 mm * Storage for max. 9 pairs of plug-in stakes approx. 100x50 mm, inside front wall * One INOX toolbox, approx. 1,500 x 390 x 810 mm, under the loading platform, left and right in direction of travel * Four warning signs extendable by approx. 400 mm,