Pracovná plošinová náves

FAYMONVILLE MAX410 Ballastauflieger

Our complete stock of immediately and short-term available vehicles can be found on our website.

Excerpts from the equipment. Complete specification available upon request.

Load area:
* Load platform with approx. 30 mm thick hardwood floor
* 8 pairs of external folding lashing rings (LC 10,000 daN)

Landing gear:
* JOST landing legs (mechanical) with two-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load)

Tyres:
* 385/65 R 22.5
* TPMS tyre pressure monitoring system according to ECE R 141. Data transmission to the truck is via the standardised EBS interface in accordance with ISO 11992. The truck must support data transmission and display for correct operation.

Axles and suspension:
* BPW axles, technical capacity per axle 10,000 kg
* 1st and 3rd axles hydro-mechanically forced steered, mounted on turntable, 2nd axle fixed
* Air suspension with raise/lower valve
* Axle tool

Braking system:
Fpjdpfjxl Nf Rox Agusn
* Wabco braking system according to EU regulations with EBS-E (4S3M), without connections to the tractor unit

Electrical system:
* Electrical system according to EU regulations, 24 Volt lighting ASPÖCK-NORDIK (ASS3)
* ASPÖCK-UNIBOX mounted on the front connection strip with sockets 24N, 24S & 15-pin connector according to ISO standards
* 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098

Steel construction:
* Structure made of high-strength fine-grained steel
* Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa)

Paintwork:
* Entire steel structure automatically shot-blasted after welding using a blast wheel machine
* Second blasting with corundum for optimum coating adhesion
* Final coating with 2 layers of 2K topcoat, single colour in RAL 3002 Carmine Red in compliance with the RAL system 841GL
* Rear section metallised and painted in RAL 9010 (Pure White)
* Wheel rims in silver
* Paint system tested with salt spray test as per ISO 9227-NSS
* Cavity sealing with special wax

Accessories:
* Load platform with approx. 30 mm thick hardwood floor
* 2-inch kingpin
* One galvanised steel front wall (EN12642-XL), approx. 1,200 mm high
* At the front galvanised connection strip, yellow-red air couplings
* 4 wheel chocks with holder on the front wall
* Storage for approx. 1,000 mm plug-in posts at the central rear beam
* On gooseneck and rear panel, left and right, each with a holder for warning boards including socket
* Yellow reflective tape according to EU regulations on sides and rear of the trailer
* 10 pairs of post sockets for approx. 100 x 50 mm plug-in posts in the outer frame of the load platform
* European reflective plates (Red-Yellow) on the rear of the trailer
* Bracket for a rotating beacon at the rear of the trailer
* One mudflap at the rear of the trailer
* Manual and documentation on USB stick
* Speed sticker 80 km/h on rear and both sides
* Electro-hydraulic power unit
* 1 shunting coupling with reinforcement, bolted to the rear crossmember
* Load gauge for determining axle loads including load chart
* Central lubrication system BEKAMAX (Pico) with standard grease NLGI-2 and removable cover for the pump
* Remote steering front and rear via cable remote control with push buttons, with axle tracking control (without installation in the tractor unit)
* 7 pairs of galvanised plug-in posts approx. 100 x 50 mm, approx. 1,000 mm high
* 4 pairs of cross rails for post sockets, installed transversely in the platform, for plug-in posts approx. 100 x 50 mm
* Spiral cable for supplying t

Inzercia bola automaticky preložená a vyskytli sa nejaké chyby prekladu.