Arburg Allrounder 520 S 1600-290 / 290

Arburg Allrounder 520 S 1600-290 / 290

This 6-axis Arburg Allrounder 520 S 1600-290 / 290 was manufactured in 2015. It features a highly wear-resistant thermoplastic cylinder with a diameter of 30 mm and a drive unit powered by a 30 kW motor. The machine is equipped with advanced controls for both injection units and supports multi-component processing. If you are looking for a high-quality injection molding machine, you should consider the hydraulic injection molding machine Arburg Allrounder 520 S 1600-290 / 290, which we have for sale. Contact us for further details.

• Injection Units and Plasticizing
• 1st Injection Unit:
• Complete thermoplastic cylinder, 30 mm, highly wear-resistant
• Programmable, controlled nozzle contact force
Ncsdpfjyxdwdox Abbsp
• aXw ScrewPilot control system
• 2nd Injection Unit:
• 2nd injection unit 290, vertical
• Complete thermoplastic cylinder, 30 mm, highly wear-resistant
• Open nozzle, 30 mm with nozzle tip; extended nozzle tip +20 mm; radius 15
• Heating band for open nozzle
• Programmable, controlled nozzle contact force
• aXw ScrewPilot control system
• Standard worm gear coupling; coupling geometry: both sides
• Multi-component processing; separating plane device on short runners for the 2nd unit
• Injection with mold closing ("flying injection")

• Drive, Hydraulics, and Cooling
• Drive unit with 30 kW motor
• 65 l/min charging flow rate
• Pressure accumulator module, 64 l storage volume (max. 230 bar); accumulator drive
• Continuous oil cooling and filtration; increased cooling capacity
• Controlled machine cooling circuits

• Clamping System, Ejector, and Core Pulls
• Clamping plate set; central Ø 125 mm
• Minimum installation height 450 mm (extended)
• Ejector pressure P/Q controlled (requires T2); ejector cross
• Core pulls:
• Core pull 1 simultaneous movement (P/Q controlled, programmable)
• Core pull 2 simultaneous movement (P/Q controlled, programmable)
• Core pull 3 simultaneous movement (P/Q controlled, programmable)
• Pneumatic core pull control 4 including pressure regulator
• Electric core pull control 1 (requires VE 436/00)

• Mold Connections Pneumatics/Hydraulics
• Electric connection pneumatic NVD 1 (in the mold)
• Electric connection pneumatic NVD 2 (in the mold)
• Electric and hydraulic connection NVD 3 (in the mold)
• Electric and hydraulic connection NVD 4 (in the mold)
• Blow-off device 1 with pressure regulator; connection for blow-off device 2

• Cooling Water and Mold Circuit
• Shut-off valve for cooling water (inlet); shut-off valve for cooling water (inlet 2)
• Cooling water filter 100 µm (inlet)
• 3 cooling water circuits to the fixed platen; 3 cooling water circuits to the moving platen
• Standard equipment for 2nd cooling water distributor (manual) with 7 free cooling circuits

• Controls and Electrical Equipment
• Selogica direct control; technology level
• Heating circuit protection (1-6 with 16 A)
• 15 electric heating circuits for mold heating
• Boost function for heating circuits (hot runner)
• Upper safety guard open, raised to safety distance
• Error indicator with warning light
• Operator authorization via chip card (EUROMAP 65)

• Interfaces and Connectivity
• Interface for conveyor belt (machine base)
• Prepared for six-axis robot with SELOGICA interface
• Robot interface (EUROMAP 67), 50-pin
• Emergency stop interface (24-pin, 2-channel)
• Standard equipment for elec

Inzerát bol automaticky preložený. Chyby v preklade sú možné.